مشاهدة النسخة كاملة : ما هى الماده المستعمله فى طلاء المسدس


احمد العوضى
11-03-23, 10:23 PM
ارجو الافاده هل يعلم احدكم اسم الماده المستخدمه فى طلاء المسدس باللون الاسمر لانى محتجه فى شغل خاص بى يا احلا منتدى:rolleyes:

بسام سعيد
11-03-24, 12:40 PM
يارب حد يرد لاني دوخت على الموضوع ده
ومحدش رد عليا

احمد العوضى
11-03-25, 12:17 AM
انا كنت شفت مره واحد جاب فديو لعبوه صغيره بها ماده تحول لون المسدس الى الون الاسود لاكن لا اعلم اسم المركب الله اعلم

EGYFALCON73
11-03-28, 01:09 AM
يمكن اعادة طلاء الاسلحة القديمة التي فقدت اللون الاسود الواقي للفولاذ
هناك عدة طرق سهلة يمكن تطبيقها اولا على قطعة فولاذ قديمة للممارسه قبل تطبيقها على
السلاح الشخصي



الطريقة الاولى
قم بغسل الاجزاء التي يراد طلائها جيدا من الزيوت والاوساخ
وذلك باستخدام الصابون المستخدم لتنظيف الصحون مع فرشاة
ثم اغسل القطعة بالماء

قم باضافة 750 غرام من مادة الصودا الكاويه + 50 غرام من اوكسيد الرصاص - لكل لتر من الماء
بعد الذوبان قم بتسخين الخليط الى ان تصل درجة الحراره 115° C ضع القطعه المراد طلائها في الحوض
لمدة 30/40 دقيقه بعد ذلك اغسل القطعة بالماء المغلي -



الطريقة الثانية
3 لتر من الماء + 2 كلغم من الصودا الكاوية (NaOH) + نترات البوتاسيوم (KNO3

EGYFALCON73
11-03-28, 01:12 AM
Bluing of iron

Iron object can give different color from light orange to dark blue one only by heating, and painting it depends on the degree of heating object. When heated to 220 ° - turns bright orange, to 225 ° - Orange, 235 ° - yellow, 277 ° - purple, 280 ° - blue, 299 ° - blue, 316 ° - black and blue.


Greenish-brown (for rifle barrels)

1 wt. hours of antimony trichloride pounded by heating with 3 wt. hours of olive oil, the mixture is applied to the surface of the object with a thin layer through cloth and leave the subject in this form for 24 hours. After this period the subject becomes rusty, and when repeated procedures - brown. Bluing is repeated until the desired color. Usually it takes 10-12 days, the process is faster in a warm room. After bluing subject thoroughly washed, dried, polished stone or polishing with lacquer or varnish.


Blue

Make up a mixture of a solution of 140 g sernovatistokislogo sodium (hyposulfite) in 1 liter of water and 35 g of lead acetate in 1 liter of water. In this mixture is immersed object and keep it until he takes a dark blue color. Good solution is heated to a boil.

You can also use a mixture of solutions:

1 wt. h. red blood salt in 200 g of water and 1 wt. hours of ferric chloride, 200 g of water. Immersed in the mixture treated subjects, painting a very strong, but indicated the mixture should be applied with caution as it is poisonous.


Red-brown

Dissolve 15-20% of ferric in 1 liter of water replacement of water with alcohol or denatured alcohol can give better results and smooth color. The solution is applied to the subject twice with an interval of several hours, then treated with iron plaque formed brush and once again cause the solution. After bluing object is covered with varnish or linseed oil.


Dark brown

Objects immersed in a solution of 30% ferrous sulfate, 15% ferric chloride, 12 g of honey nitrate in 1 liter of water, to which is added a bit of denatured alcohol. It is better instead of dipping strike brush for this solution and let dry out! Emerging rusty plaque brushes brush and repeat the operation until such time until you have a solid dark brown.


Black

Here are some recipes:


The subject is immersed in 10% solution of potassium bichromate (potassium bichromate) for 15-20 minutes, removed, dried in the air and hold for two minutes over a strong burning, but not smoky coals. After the first time turns black-brown staining. If this operation be repeated several times, we get a pure black color.


The subject is covered evenly with a thin layer of linseed oil or linseed oil and heat over a very hot burning charcoal (without ash). A layer of oil with coal and burns. This operation is repeated several times. After each heating and cooling of the object rubbing a dry cloth. The last time the object is heated slightly, and rubbing produce cloth dampened with a linen drying oil.


Purified first object subjected mordant, ie, it is immersed in his short time in a mixture of 1 wt. hours of concentrated sulfuric acid and 20 wt. hours of water. For so the object is washed, dried and cover cooked on a steam bath solution of 1 wt. h. The sulfur in 16 wt. h. Turpentine, then the object slightly heated until a black film.

When necessary, cover the solution of sulfur and heating is repeated.


For blackening of iron products in the black they dipped into the solution of 5-10 wt. pm copper sulfate, and 5-10 wt. hours of sulfuric acid in 100 wt. h. water, washed with water and immersed in a solution of 6 wt. h. sulfuric liver and 20 g of ammonia in 100 wt. hours of water.

EGYFALCON73
11-03-28, 01:15 AM
http://www.youtube.com/watch?v=qM_Z1Tax2k0

mahmoud el masry
11-03-28, 12:48 PM
بس خد بالك الكلام دة مينفعش مع مسدسات الصوت الان مسدسات الصوت من الانتيمونيا

mosho
11-03-28, 01:15 PM
ينفع مع البنادق الرش؟؟؟

mahmoud el masry
11-03-28, 01:41 PM
ينفع مع بنادق الرش والمسدسات الحى بس نصيحة لوجة الله وديها لورشة سلاح يعملهالك احسن

احمد العوضى
11-03-30, 03:01 AM
متشكر جدا جدا

Eng Badran
11-03-30, 06:11 PM
يا جماعة انا عايز اعرف ازاي اطلي مسدسات الصوت لان عندي واحد في الضياع خااااالص